- Guaranteed Secure Payments on Every Order
- Refund if your item is not delivered or as described
- Buyer Protection after order confirmation
- Place of Origin: China
- Brand Name: Hydraulic Co., Ltd. Qidong City, Texas
- Model Number: A2FO/M
- Weight: 25.000 kg
Quantitative pump A2F0
6 series, for the open loop axial cone plunger - bending design
Specification 16-180
Nominal pressure 40Mpa peak pressure 45 Mpa
A2F0 axial pump for open loop hydrostatic drive.
The output flow rate is proportional to the driving speed and displacement.
This kind of pump is used in mechanical or industrial field. Design of drive shaft bearing
To make it achieve the desired service life in the field of application.
A variety of specifications can be matched with each actual drive.
--- good power / weight ratio
--- small size
Best efficiency
Economic design
Conical plunger piston ring seal
Because the product model specifications are more, please be sure to check clearly, in the full note!
The normal delivery period is 1 ~ 3 days, and the quantity of the goods should be confirmed as the delivery time!
Working pressure
Oil port S minimum inlet pressure min=0.08Mpa Pabs (absolute pressure)
The oil inlet pressure of S is related to the speed of the pump (see Figure 1).
The maximum pressure of oil port A or B
Shaft extension Z axis extension B, A, P axis extension Z, P
(radial force at the end of the shaft)
Rated pressure 40Mpa 35Mpa PN 31.5 Mpa
Maximum pressure 45Mpa 40Mpa Pmax 35 Mpa
Shell drain pressure (oil port T)
PT = 0.1Mpa
Working medium
Mineral oil can be used
Oil temperature
Operating temperature range: -25 to 80
Oil viscosity
The best viscosity: 16 ~ 36m (/s square meters in the operating temperature range)
The maximum allowable viscosity: 1000m square meters /s (instantaneous running in the cold start)
The minimum allowable viscosity: 10M square meters (/s in the leakage of the oil temperature is 90 degrees centigrade instantaneous operation)
Oil filtration accuracy
Recommended filter accuracy of 10 M filter, the most crude shall not exceed 25 m accuracy.
Installation location
Optional, the shell must always be filled with hydraulic oil.
Oil flow direction
From the end of the axis to observe the clockwise rotation of S to B
Counter clockwise rotation S / A
Product quality is stable, price concessions, please call or email!
E-mail: 643921642qq.com
Cell phone: 0086-18962820125
定量泵A2F0 | |
规格16-180 | 公称压力40Mpa 峰值压力45 Mpa |
A2F0斜轴式轴向定量泵,适用于开式回路的静液压驱动。 输出流量与驱动转速和排量成正比。 多种规格可与每个实际驱动相匹配。 ---良好的功率/重量比 ---外形尺寸小 ---最佳效率 ---经济的设计 ---锥形柱塞采用活塞环密封 |
工作压力 油口S的最低进油压力 Pabs min=0.08Mpa(绝对压力) 油口S的进油压力与泵的转速有关(见图一) 油口A或B的最高压力 轴伸A 轴伸Z、B、P 轴伸Z、P (轴端有径向力) 额定压力PN 40Mpa 35Mpa 31.5 Mpa 最高压力Pmax 45Mpa 40Mpa 35 Mpa 壳体泄油压力(油口T) PT≤0.1Mpa 工作介质 矿物油基本都可选用 油液温度 工作温度范围:-25℃~80℃ 油液粘度 最佳工作粘度:16~36m㎡/s(在工作温度范围内) 最小允许粘度:10m㎡/s(在泄漏油温度为90℃时瞬时运行) 油液过滤精度 推荐过滤精度为10μm的滤油器,最粗不得超过25μm的精度。 安装位置 任选,壳体内必须始终充满液压油。 油流方向 从轴端观察 顺时针旋转S→B 逆时针旋转S→A |
因产品型号规格较多,请务必核对清楚,在备注中完整写明!
小批量订货正常交货期为1~3天,批量大时需先确认交货期!
产品质量稳定,价格优惠,欢迎致电或邮箱咨询!
邮箱:643921642@qq.com
手机: 0086-18962820125
- Place of Origin: China
- Brand Name: Hydraulic Co., Ltd. Qidong City, Texas
- Model Number: A2FO/M
- Weight: 25.000 kg
Quantitative pump A2F0
6 series, for the open loop axial cone plunger - bending design
Specification 16-180
Nominal pressure 40Mpa peak pressure 45 Mpa
A2F0 axial pump for open loop hydrostatic drive.
The output flow rate is proportional to the driving speed and displacement.
This kind of pump is used in mechanical or industrial field. Design of drive shaft bearing
To make it achieve the desired service life in the field of application.
A variety of specifications can be matched with each actual drive.
--- good power / weight ratio
--- small size
Best efficiency
Economic design
Conical plunger piston ring seal
Because the product model specifications are more, please be sure to check clearly, in the full note!
The normal delivery period is 1 ~ 3 days, and the quantity of the goods should be confirmed as the delivery time!
Working pressure
Oil port S minimum inlet pressure min=0.08Mpa Pabs (absolute pressure)
The oil inlet pressure of S is related to the speed of the pump (see Figure 1).
The maximum pressure of oil port A or B
Shaft extension Z axis extension B, A, P axis extension Z, P
(radial force at the end of the shaft)
Rated pressure 40Mpa 35Mpa PN 31.5 Mpa
Maximum pressure 45Mpa 40Mpa Pmax 35 Mpa
Shell drain pressure (oil port T)
PT = 0.1Mpa
Working medium
Mineral oil can be used
Oil temperature
Operating temperature range: -25 to 80
Oil viscosity
The best viscosity: 16 ~ 36m (/s square meters in the operating temperature range)
The maximum allowable viscosity: 1000m square meters /s (instantaneous running in the cold start)
The minimum allowable viscosity: 10M square meters (/s in the leakage of the oil temperature is 90 degrees centigrade instantaneous operation)
Oil filtration accuracy
Recommended filter accuracy of 10 M filter, the most crude shall not exceed 25 m accuracy.
Installation location
Optional, the shell must always be filled with hydraulic oil.
Oil flow direction
From the end of the axis to observe the clockwise rotation of S to B
Counter clockwise rotation S / A
Product quality is stable, price concessions, please call or email!
E-mail: 643921642qq.com
Cell phone: 0086-18962820125
定量泵A2F0 | |
规格16-180 | 公称压力40Mpa 峰值压力45 Mpa |
A2F0斜轴式轴向定量泵,适用于开式回路的静液压驱动。 输出流量与驱动转速和排量成正比。 多种规格可与每个实际驱动相匹配。 ---良好的功率/重量比 ---外形尺寸小 ---最佳效率 ---经济的设计 ---锥形柱塞采用活塞环密封 |
工作压力 油口S的最低进油压力 Pabs min=0.08Mpa(绝对压力) 油口S的进油压力与泵的转速有关(见图一) 油口A或B的最高压力 轴伸A 轴伸Z、B、P 轴伸Z、P (轴端有径向力) 额定压力PN 40Mpa 35Mpa 31.5 Mpa 最高压力Pmax 45Mpa 40Mpa 35 Mpa 壳体泄油压力(油口T) PT≤0.1Mpa 工作介质 矿物油基本都可选用 油液温度 工作温度范围:-25℃~80℃ 油液粘度 最佳工作粘度:16~36m㎡/s(在工作温度范围内) 最小允许粘度:10m㎡/s(在泄漏油温度为90℃时瞬时运行) 油液过滤精度 推荐过滤精度为10μm的滤油器,最粗不得超过25μm的精度。 安装位置 任选,壳体内必须始终充满液压油。 油流方向 从轴端观察 顺时针旋转S→B 逆时针旋转S→A |
因产品型号规格较多,请务必核对清楚,在备注中完整写明!
小批量订货正常交货期为1~3天,批量大时需先确认交货期!
产品质量稳定,价格优惠,欢迎致电或邮箱咨询!
邮箱:643921642@qq.com
手机: 0086-18962820125